国产毛片a精品毛-国产毛片黄片-国产毛片久久国产-国产毛片久久精品-青娱乐极品在线-青娱乐精品

電子工程網

標題: a3p060 燒寫問題 [打印本頁]

作者: wangkj 時間: 2009-6-25 14:32
標題: a3p060 燒寫問題
我吧vjtag,vpump直接接到3.3V了。
出現這個錯誤：
programmer 'FPBBALTLPT1' : Scan Chain FAILED.

是不是vjtag必須接上拉電阻？
vpump必須用電容?

如果需要，要多大的？

programmer 'FPBBALTLPT1' : Scan Chain...
Error: programmer 'FPBBALTLPT1' : Signal Integrity Failure
   Integrity Check Pattern Not Found.
   Integrity Check Pattern :
   550FAAF000FF0000FFFF
   IrScan Error.
   TDO stuck at 0
   Chain Analysis Failed.
Error: programmer 'FPBBALTLPT1' : Data Bit length : 8272
Error: programmer 'FPBBALTLPT1' : Compare Data  :0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
Error: programmer 'FPBBALTLPT1' : Scan Chain FAILED.
Error: Failed to run Action.

作者: wangkj 時間: 2009-6-25 14:32
貌似我找不到 fpga/cpld應該劃分到那個類別，5個主題好像都不太合適。

作者: wangkj 時間: 2009-6-25 14:33
網上找到的答案是vjtag 200歐電阻上拉，vpump加電容。

作者: wangkj 時間: 2009-6-25 14:34
[qq]1248780[/qq]
這是原理圖。

mini2440_20090518.pdf

164.97 KB, 下載積分: 積分 -1

作者: wangkj 時間: 2009-6-27 10:10
可能是vjtag的問題，飛線比較難辦。
實驗室的門開不開了，只好回家用自己的設備了。
以前是能開開的，唉，郁悶。

作者: wangkj 時間: 2009-6-27 10:10
還得給自己的電腦安裝軟件。

作者: wangkj 時間: 2009-6-27 12:03
另外的說法就是去掉r4,r5電阻。

作者: wangkj 時間: 2009-6-29 10:40
拆掉那兩個電阻，vjtag 加200歐姆電阻，故障依舊。
看來得找個usb的編程器了。
俺自己想辦法。不知道誰有賣的。

作者: wangkj 時間: 2009-7-1 12:16
用usb的燒寫器好了。

作者: hushucon 時間: 2010-10-11 19:36
回復1樓wangkj：

作者: hushucon 時間: 2010-10-11 19:37
問題解決了嗎，我遇到了和你一樣的問題，能知道下嗎？ 回復1樓wangkj：

歡迎光臨電子工程網 (http://www.qingdxww.cn/)